Non-standard T-bolts in mixed sizes laid out on a steel bench, one fitted with a T-nut and washer

Non-standard T-bolt sets

Non-standard T-bolts,
made as one matched set.

Our main line: non-standard T-bolts, kitted with matching T-nuts and washers to your drawing — M5–M90, up to 3,000 mm. Standard T-bolts and general fasteners come off the same floor in Yuyao.

Three product lines

Non-standard first.
Standard second.
General parts third.

  1. 01

    Non-standard T-bolt set Main line

    T-bolt, T-nut and washer kitted as one set and matched to your drawing — M5 to M90, lengths up to 3,000 mm.

  2. 02

    Standard T-bolt

    Square neck, round neck and double-rib series, held in stock in the common sizes.

  3. 03

    General fasteners

    Hex bolts, nuts and washers, plus stamped and turned parts from the same floor.

FIG. 01 — T-BOLT SET

Bolt
T-head, rolled thread
Nut
T-nut, matched class
Washer
Flat, matched OD
Finish
HDG / zinc flake

M8 – M90 · 20 – 3,000 mm · made to your drawing

Thread range
M5 – M90
Length
20 – 3,000 mm
Property class
4.6 – 12.9
Fatigue
6M cycles · QA1
Salt spray
up to 1,000 h

Capability — one roof

Forging, threading, heat treatment, coating — in house.

Forging, thread rolling, heat treatment and coating all happen inside the same fence. Nothing critical is subcontracted, which is why the batch records actually match the parts.

Plant & equipment →
01

Cold heading

Multi-station cold heading forms the head, shoulder and rib in one pass. Wire is bought against mill certificate, heat number logged against every lot.

  • M5 – M24
  • Multi-station
  • Heat-number traceable
02

Hot forging

For large and extra-long parts — up to M90 and 3,000 mm — where cold forming runs out of press capacity. Grain flow follows the head geometry.

  • Up to M90
  • 3,000 mm max
  • 42CrMoA
03

Thread rolling & CNC

Rolled thread for fatigue-critical joints, CNC turning and milling for specials, lock plates and drawn components.

  • Rolled 6g
  • CNC turning
  • Special heads
04

Heat treatment

Quench and temper to classes 8.8 / 10.9 / 12.9 with hardness curve recorded per batch, no decarburised layer on the thread.

  • 8.8 – 12.9
  • Hardness logged
  • No decarb
05

Anti-corrosion coating

Hot-dip galvanising, zinc flake, DAC-type coatings and stainless systems specified by corrosivity category — C1 through CX.

  • HDG
  • Zinc flake
  • C1 – CX
06

Assembly & kitting

Washer and nut pre-assembled onto the bolt, kitted per channel set, so the installer handles one part instead of four.

  • Pre-assembly
  • Kitting
  • Export packing
12M+ pcs
Annual output

T-bolts and special fasteners

6M cycles
Fatigue life

QA1 grade, production bolts

7,000m²
Manufacturing site

Hemudu, Yuyao — since 2005

1,000h
Salt spray

Heavy-duty coating systems

Process — drawing to container

From wire coil to export carton.

A lot number follows the wire coil through every station. If a customer asks which heat a carton came from, we answer in one query.

  1. 01

    Wire in

    Coil received with mill cert, heat number logged.

  2. 02

    Forming

    Cold heading or hot forging of head and ribs.

  3. 03

    Thread rolling

    Rolled to 6g — fatigue-critical, not cut.

  4. 04

    Heat treatment

    Quench & temper, hardness curve recorded.

  5. 05

    Coating

    HDG / zinc flake / DAC, thickness mapped.

  6. 06

    Inspection

    Fatigue, salt spray, hardness, 3.1 certificate.

Applications

Where our fasteners are used.

Six sectors carry most of our volume. Each one has its own coating package, documentation set and inspection level.

01

Rail & rolling stock

T-bolts and special bolts for bogies, equipment cabins, skirt panels and track fastening — supplied into high-speed rail and metro programmes.

BogieSkirt panelsTrack fastening
02

Nuclear power

Safety-class fasteners with documented process control, material certificates and lot traceability for nuclear-grade bolting.

Safety class3.1 certLot trace
03

Wind power

Blade bolts and high-tensile large-diameter bolts up to M90 in 42CrMoA, with heavy-duty coating for coastal and offshore duty.

Blade boltsM90Offshore coating
04

Construction & infrastructure

Anchor and foundation bolts, embedded-channel T-bolts, lock plates and cast-in channel sets for precast and steel structures.

AnchorsCast-in channelPrecast
05

Commercial vehicles

Truck T-bolts and non-standard automotive parts under IATF 16949 process control, with PPAP documentation where required.

IATF 16949PPAPTruck T-bolts
06

Stamped parts & hinges

Progressive-die stamping, hinges, brackets and assemblies — plus cabinet, tool-box and skirt locks.

Progressive dieHingesLocks

On site

Seven thousand square metres, one product.

More from the plant →
Lingqi plant, workshop and exhibition photograph 1
Lingqi plant, workshop and exhibition photograph 2
Lingqi plant, workshop and exhibition photograph 3
Lingqi plant, workshop and exhibition photograph 4
Lingqi plant, workshop and exhibition photograph 5
Lingqi plant, workshop and exhibition photograph 6

Quality

Test data and certificates with every shipment.

Every shipped lot carries a 3.1 inspection certificate with hardness, coating thickness and thread gauge results. Salt spray and proof load data are attached where the specification calls for them.

  • EN 10204 3.1 mill certificate
  • PPAP Level 3 on request
  • RoHS / REACH declaration
Testing & standards
TestStandardOur spec
FatigueServo-hydraulic3 M / 6 M cycles · QA1
Salt sprayISO 9227Up to 1,000 h
Tensile / proof loadISO 898-1Per property class
HardnessISO 6508Recorded per batch
Hydrogen embrittlementBaked after platingPer coating route
Thread gaugeISO 15026g go / no-go
ISO 9001:2015Quality management
ISO 14001:2015Environment
ISO 45001:2018Occupational safety
IATF 16949:2016Automotive quality
EN 10204 3.1Inspection certificate
Hi-Tech EnterpriseNational recognition

FAQ

Frequently asked questions.

Drawings, minimums, certificates, coating choices. If something is missing, ask directly — engineering answers in English, German or Chinese.

Cannot find your size?

Send the drawing and we will tell you honestly whether our tooling covers it.

Ask engineering
Do you work from customer drawings?

Yes. Custom non-standard components are the core of the business — send a drawing or a sample and first articles follow in 10–15 days, with flexible MOQ.

What is the size range?

M5 to M90, lengths from 20 mm to 3,000 mm. The largest part produced to date is an M125 × 3,000 mm T-bolt in class 8.8, 42CrMoA, weighing 296 kg.

Which property classes and materials?

Classes 4.6, 4.8, 5.6, 6.8, 8.8, 10.9 and 12.9 in carbon and alloy steel (42CrMoA and similar); stainless A2-50 / A4-50 / A2-70 / A4-80. Non-standard material on request.

How is fatigue performance verified?

Fatigue life is validated on production bolts on servo-hydraulic equipment — 3 million cycles for standard programmes, 6 million cycles at QA1 grade for safety-critical joints.

What coating do you recommend for coastal projects?

Heavy-duty systems are selected by corrosivity category C1–CX: hot-dip galvanising, zinc flake or DAC-type coatings, salt-spray tested up to 1,000 h to ISO 9227.

RFQ

Send the drawing.
Quote in 24 hours.

PDF, STEP or a photo of the old part with a caliper reading — all fine. We come back with DFM comments, price breaks and a delivery date.

24hours
drawing to quote
M–S · GMT+8